The Daniel Defense V7 LW is five ounces lighter than the standard V7. It uses our Modular Float Rail (MFR) 12.0, providing each shooter with the ultimate in modular adaptability. Should the shooter desire, the tube can be run “slick” with an uninterrupted top rail that runs the length of the tube. In addition, the 3” Modular Picatinny Rail sections allow the shooter to customize the rail set up. The DDM4v7 is equipped with a single pinned low profile gas block that is drilled, taper reamed, and press fit into place to securely attach the low profile gas block to the barrel assembly. This rifle also comes with the newly designed, rugged and comfortable Daniel Defense Buttstock and Pistol Grip.
MATERIALS & CONSTRUCTION
•LOWER RECEIVER: Mil-Spec with Enhanced Flared Magazine Well and Rear Receiver QD Swivel Attachment Point. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
•UPPER RECEIVER: Mil-Spec with Indexing Marks and M4 Feed Ramps. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
•BARREL: Chrome Moly Vanadium Steel, Cold Hammer Forged, 1:7, 16″ Lightweight Profile, Mid-length Gas System, Chrome Lined, MP tested, and Mil-Spec Heavy Phosphate coated
•GAS SYSTEM: Pinned Low Profile Gas Block CNC Machined of 4140 hardened steel and Mil-Spec Heavy Phosphate Coating, Mid-length, Direct Impingement
•MUZZLE DEVICE: Daniel Defense Flash Suppressor, 17-4 PH Stainless Steel, Salt Bath Nitride Finished
•BOLT CARRIER GROUP: M16 Profile, Mil-Spec MP Tested, Chrome Lined, Properly Staked Gas Key
•BUFFER: H Buffer
•SIGHTS: Sold Separately
•HANDGUARD: Daniel Defense Modular Float Rail™ 12.0, CNC Machined of 6061-T6 Aluminum, with three Modular Picatinny Rail Sections, Type III Hard Coat Anodized
•RECEIVER EXTENSION: 6 Position Mil-Spec 7075-T6 Aluminum
•BUTTSTOCK: Daniel Defense Buttstock, Glass Filled Polymer with Soft Touch Overmolding
•PISTOL GRIP: Daniel Defense Pistol Grip, Glass Filled Polymer with Soft Touch Overmolding
•RAIL LADDERS: 3 low profile ladders made from Santoprene, heat resistant to 300° F.
•Made in the USA!
Please Note: This description may represent a general group of products. Please read the item's title and specifications for more specific information about this particular item.
|Manufacturing # / SKU
||32 ¼” – 35 7/8”
||Magpul PMAG 30-Round
||Daniel Defense Full-Latch Impact Plastic Case
Restricted Product Information
Guns can only be shipped to a location within the USA that holds an FFL (Federal Firearms License) - this can be your local gun shop, pawn shop, sporting goods store, etc. Your local gun dealer will then handle the transfer of the firearm to you.
Please ensure that you have familiarized yourself with the process before placing a firearm order. Please note that you must confirm your acceptance of all of these policies to place a firearm order:
Write a review & get a $5 coupon
Submitted By: David S. On 05/28/2015
Due to weather in W CO, I haven't had a chance to put more than about 90 rounds down the pipe. But this is a great rifle. Incredibly light and easy to handle. Daniel Defense quality is impeccable. I'm not a fan of quad rails, so the hand guard is excellent as well. The short rails are nice to move around, right now I have two on the bottom, and a third at 0300. I put Troy flip irons on it, and may not go for optics. I highly recommend it.
[5 of 5 Stars]